ISO 3601 O Ring

ISO 3601 O Ring
Product Introduction:
ISO 3601 O rings are important sealing components used in hydraulic systems, pneumatic equipment and general industrial applications. They are mainly used to prevent the leakage of liquids and gases while meeting standardized dimensional and tolerance requirements, helping ensure consistent fit, reliable sealing and dependable equipment operation.
Send Inquiry

Ningbo Zhonggao Rubber & Plastic Manufacturing Co., Ltd. is one of the most reliable manufacturers and suppliers of iso 3601 o ring in China. The company has world-leading production equipment and strong manufacturing capabilities. Welcome to wholesale custom made iso 3601 o ring from our factory.

 

ISO 3601 O Rings

 

ISO 3601 O rings provide standardized dimensions for reliable sealing in hydraulic, pneumatic, and industrial equipment. Available in multiple rubber compounds and hardness options, they help buyers ensure dimensional compatibility, media resistance, and consistent sealing performance across maintenance and OEM applications.

 

 

Technical Specifications

 

Rubber Material Selection:

 

Rubber Material

Key Performance

NBR

Mineral Oil, Hydraulic Fluid & Fuel Resistance

HNBR

Heat, Oil, Hydraulic Fluid & Wear Resistance

FKM

High-Temperature, Oil & Chemical Resistance

EPDM

Water, Steam, Ozone & Weather Resistance

VMQ (Silicone)

Wide-Temperature Flexibility & Low-Temperature Elasticity

FFKM

High-Temperature & Aggressive Chemical Resistance

 

ISO 3601 O Ring Specifications:

 

Specification

Reference Value / Range

Size Standard

ISO 3601

Inner Diameter (ID)

1–1,000 mm

Cross-Section Diameter (CS)

0.5–20 mm

Outer Diameter (OD)

ID + 2 × CS

Rubber Hardness

40–90 Shore A

NBR Temperature Range

−40°C to +120°C

HNBR Temperature Range

−40°C to +150°C

FKM Temperature Range

−20°C to +200°C

EPDM Temperature Range

−50°C to +150°C

VMQ (Silicone) Temperature Range

−70°C to +220°C,

FFKM Temperature Range

−20°C to +260°C

 

*Actual dimensions, tolerances, hardness, temperature limits, and chemical resistance depend on the applicable ISO 3601 requirements, selected rubber compound, and operating conditions.

 

 

Custom ISO 3601 O Ring Manufacturing

 

We manufacture custom ISO 3601 O rings based on your drawing, sample, equipment, and operating conditions.

image (15).png

 

Custom Size & Dimensions

We can produce:

  • Metric ID and cross-section dimensions
  • Sizes according to applicable ISO 3601 requirements
  • Specified dimensional tolerances
  • Non-standard dimensions for replacement and OEM applications
  • Custom dimensions based on approved drawings or samples

 

Rubber Material & Hardness

Rubber compound and hardness can be selected according to:

  • Operating temperature
  • Contact media and chemical concentrations
  • Working and peak pressure
  • Required Shore A hardness
  • Compression and compression set requirements
  • Static, reciprocating, or rotary sealing conditions

Available materials may include NBR, HNBR, FKM, EPDM, silicone (VMQ), and FFKM, depending on application requirements and compound availability.

 

Drawing / Sample

You can provide:

  • CAD or technical drawings
  • ISO 3601 size code and applicable standard edition
  • Inner diameter, cross-section diameter, and dimensional tolerances
  • Material, hardness, and performance requirements
  • Groove dimensions, clearance, and installation details
  • Existing O ring samples or original part numbers
  • Operating conditions and expected service life

We use these details to evaluate dimensional compatibility, material suitability, and sealing requirements before sample approval.

 

Groove Compatibility & Performance

Custom ISO 3601 O rings can be specified according to:

  • Groove width, depth, and clearance
  • Required compression and sealing contact
  • Pressure-related extrusion resistance
  • Friction and wear requirements for dynamic applications
  • Resistance to heat, aging, and contact media
  • Applicable dimensional inspection and performance testing criteria

These requirements help reduce installation issues and support reliable sealing under the intended operating conditions.

 

OEM & Replacement Support

We support custom requirements for:

  • Approved dimensions and tolerances
  • Rubber compound and hardness
  • Part numbers and identification labels
  • Packaging quantities and labeling specifications
  • Replacement O rings based on customer drawings or samples
  • OEM production according to approved specifications

For replacement projects, we recommend verifying dimensions, material compatibility, groove design, and operating conditions before approving an alternative O ring for bulk production.

 

 

ISO 3601 O Ring Applications

 

ISO 3601 O rings support sealing requirements across industrial systems, with size, rubber compound, and hardness selected to match each application`s operating conditions.

  • Hydraulic Systems
  • Pneumatic Equipment
  • Pumps & Valves
  • Automotive Components
  • Industrial Machinery
  • Water & Fluid Handling Equipment
  • Chemical Processing Equipment

 

 

ISO 3601 O Ring Manufacturing Capability

 

We operate a 5,000 m² factory with 20 production lines, over 20,000 molds, and 40+ experienced technicians, supported by mold design and manufacturing, rubber material selection, vulcanization molding, and automated inspection capabilities.

For ISO 3601 O rings, these resources support production based on standard dimensions, approved drawings, or samples, helping buyers match material and dimensional requirements, validate samples before bulk orders, and scale supply for repeat purchasing. Our factory`s capacity of up to 10 million rubber parts per month supports larger-volume demand.

 

 

ISO 3601 O Ring Quality Control

 

image.webp
  • Dimensional Inspection

Inner diameter, outer diameter, cross-section, and dimensional tolerances are checked against the approved drawing and applicable ISO 3601 requirements.

  • Material & Hardness Verification

Rubber material, Shore A hardness, and compound specifications are verified against the approved material requirements to support compatibility with operating media and conditions.

  • Visual Defect Inspection

O rings are checked for cracks, bubbles, flash, cuts, surface damage, and molding defects that may compromise sealing performance.

  • Sealing Performance Evaluation

Compression behavior, compression set, and media resistance are evaluated according to the selected compound and application requirements.

  • Sample Validation & Replacement Approval

Samples or replacement O rings are checked for dimensional fit, material compatibility, groove matching, and operating conditions before bulk production approval.

  • Compliance & Traceability

Applicable inspection records, material documentation, and certification requirements are reviewed according to the order specifications to support quality verification and batch consistency.

View Our Quality Inspection Process

 

 

B2B Ordering & Supply Support

 

Sample Lead Time: Samples are available in 3–15 days, helping buyers verify dimensions, material suitability, and fit before committing to bulk orders.

Bulk Production Lead Time: Standard order delivery typically takes 10–30 days after order details and production requirements are confirmed, with timing dependent on order quantity and customization.

MOQ: MOQ is flexible according to O ring size, rubber material, tooling requirements, and order quantity, supporting both trial orders and repeat purchasing.

Packaging & Identification: Packaging and labeling requirements can be specified by order to help buyers organize O rings by size, material, part number, or batch.

Shipping & Trade Terms: EXW, FOB, CFR, and CIF terms are available, allowing buyers to select a shipping arrangement based on destination, freight costs, and import logistics.

After-Sales Support: A 1-year quality guarantee covers manufacturing defects under normal usage conditions, giving buyers a defined basis for addressing qualifying quality issues.

Learn More About Ningbo Zhonggao

image (1).webp

 

 

FAQ

 

Q: Can ISO 3601 O rings be used as direct replacements for existing O rings?

A: Yes, provided the replacement matches the original dimensions, material requirements, groove design, pressure conditions, and operating environment.

Q: How do I prevent O rings from twisting or rolling in dynamic applications?

A: Select a suitable cross-section, compatible material, and properly designed groove, while controlling friction, lubrication, and installation conditions.

Q: When should backup rings be used with ISO 3601 O rings?

A: Backup rings are commonly used when elevated pressure or excessive extrusion clearance creates a risk of O ring extrusion.

Q: Can ISO 3601 O rings be used in vacuum sealing applications?

A: Yes, when the selected compound, surface condition, groove design, and gas permeability meet the system`s vacuum level and leakage requirements.

Q: How should ISO 3601 O rings be stored to extend shelf life?

A: Store O rings in sealed, clean packaging away from direct sunlight, ozone sources, excessive heat, moisture, and incompatible chemicals, following the applicable storage guidelines.

Q: Can non-standard O ring sizes be supplied for equipment with legacy designs?

A: Yes, custom sizes can be evaluated against customer drawings or samples when standard ISO 3601 dimensions do not fit the existing equipment.

 

 

Custom ISO 3601 O Rings for Your Project
Send your drawing or sample, ISO 3601 size code and applicable standard edition, inner diameter, outside diameter, cross-section diameter, dimensional tolerances, rubber material and compound grade, Shore A hardness, operating temperature range, contact media and chemical concentrations, working and peak pressure, static or dynamic sealing conditions, groove dimensions and extrusion clearance, lubrication requirements, expected service life, target order quantity, annual demand, testing and compliance requirements, packaging and labeling specifications, shipping destination, and required delivery schedule to receive a suitable ISO 3601 O ring quotation.

 

 

 

Hot Tags: iso 3601 o ring, China iso 3601 o ring manufacturers, suppliers, flat rubber o rings, o ring 10 mm, o ring 3 4, o ring 50mm x 3mm, o ring 8 mm, plastic o rings

 Creating Your Custom Rubber Parts Coupled with Our Masterly Manufacturing
 

OEM/ODM Services

 

Material Selection

 

Free Samples

 

Sample Delivery in 3-15 Days

 

Free Technical Consultation

 

24-Hour Response

Get A Free Quote