Pneumatic O Ring

Pneumatic O Ring
Product Introduction:
Pneumatic O rings are important sealing components used in pneumatic cylinders, valves, air compressors and other compressed-air equipment. They are mainly used to prevent air leakage between connected or moving components, while maintaining reliable sealing under pressure to ensure stable pneumatic system performance.
Send Inquiry

Ningbo Zhonggao Rubber & Plastic Manufacturing Co., Ltd. is one of the most reliable manufacturers and suppliers of pneumatic o ring in China. The company has world-leading production equipment and strong manufacturing capabilities. Welcome to wholesale custom made pneumatic o ring from our factory.

 

Pneumatic O Rings

 

Pneumatic O rings seal compressed-air systems by preventing air leakage and supporting stable equipment operation. Available in application-specific sizes, rubber materials, and hardness options, they meet sealing requirements for cylinders, valves, fittings, and industrial automation equipment.

 

 

Technical Specifications

 

Rubber Material Selection:

 

Rubber Material

Key Performance

NBR

Air Tightness, Oil & Wear Resistance

HNBR

Heat, Wear & Aging Resistance

FKM

High-Temperature & Chemical Resistance

EPDM

Water, Steam, Ozone & Weather Resistance

Silicone (VMQ)

Wide Temperature Flexibility

 

Pneumatic O Ring Specifications:

 

Specification

Reference Value / Range

Inner Diameter (ID)

2–100 mm*

Cross-Section Diameter (CS)

Typically 1.5 / 1.78 / 2.0 / 2.5 / 2.62 / 3.0 / 3.53 mm*

Rubber Hardness

40–90 Shore A*

NBR Operating Temperature

−40°C to +120°C

HNBR Operating Temperature

−40°C to +150°C

FKM Operating Temperature

−20°C to +200°C

EPDM Operating Temperature

−50°C to +150°C

Silicone (VMQ) Operating Temperature

−70°C to +220°C

Compression / Squeeze

Below 15% may cause leakage*

 

*Final specifications should be confirmed against the approved drawing and application requirements.

 

 

Custom Pneumatic O Rings

 

We manufacture custom pneumatic O rings based on your drawings, samples, sealing dimensions, rubber material, and operating conditions.

image (15).png

Custom Size & Dimensions

We can produce pneumatic O rings according to your required dimensions and tolerances:

  • Custom inner diameter (ID), outer diameter (OD), and cross-section diameter (CS)
  • Metric and inch sizes
  • Non-standard dimensions and application-specific tolerances
  • Custom sizes for pneumatic cylinders, valves, fittings, and automation equipment

 

Rubber Material & Hardness

Rubber material and hardness can be selected according to your pneumatic sealing requirements:

  • NBR: Commonly used for compressed air applications, including systems with compatible lubricating oils
  • EPDM: Suitable for selected applications involving moisture or water, subject to media compatibility
  • FKM: For applications requiring higher temperature resistance or compatibility with specific chemicals
  • Silicone (VMQ): For applications requiring a broad temperature range, where mechanical and dynamic sealing requirements permit

Hardness and compound selection should account for operating temperature, contact media, pressure, lubrication, and static or reciprocating sealing conditions.

 

Drawing / Sample

You can provide the following information for custom O ring development:

  • CAD drawings or technical drawings
  • Required ID, OD, CS, and dimensional tolerances
  • Rubber material and Shore A hardness
  • Operating temperature, pressure, and contact media
  • Existing O ring samples or part numbers

These details help evaluate dimensional fit, material suitability, and sealing requirements before sample approval.

 

Mold & Production

Custom molds and production methods can be selected according to the O ring design, dimensions, and order requirements:

  • Custom mold development for non-standard O rings
  • Compression, transfer, or injection molding, where suitable
  • Sample production for dimensional and application testing
  • Repeat production based on approved specifications and samples

 

OEM Service

We support OEM pneumatic O ring requirements, including:

  • Custom dimensions, material, and hardness
  • Customer-specific part numbers and labeling
  • Packaging according to order requirements
  • Production based on customer drawings or approved samples
  • Customer-provided molds, subject to project requirements and mold-use agreements

Drawings, samples, specifications, and other project information can be handled confidentially according to agreed requirements.

 

 

Pneumatic O Ring Applications

 

Pneumatic O rings provide sealing in a range of compressed-air systems, helping prevent air leakage and maintain reliable equipment operation across the following applications.

  • Pneumatic Cylinders
  • Pneumatic Valves
  • Pneumatic Fittings and Connectors
  • Industrial Automation Equipment

 

 

Pneumatic O Ring Manufacturing Capability

 

We manufacture custom rubber O rings for pneumatic and industrial sealing applications, supported by 5,000 m² of factory space, 20 production lines, 20,000+ molds, and 40+ experienced technicians.

  • Precision Mold Development: Molds can be designed and manufactured from customer drawings or samples, with mold-making accuracy controlled to ±0.01 mm, helping achieve dimensional fit for pneumatic sealing grooves.
  • Multiple Molding Processes: Compression, transfer, and injection molding support different O ring designs and production requirements, from custom development to repeat orders.
  • Material & Design Flexibility: With 20+ rubber material options, we can help select suitable compounds and hardness for specified compressed-air media, temperature, and sealing conditions.
  • Scalable Production: Our capacity of up to 10 million rubber parts per month can provide manufacturing resources for volume orders and ongoing supply.

 

 

Pneumatic O Ring Quality Control

 

image.webp
  • Dimensional Inspection

Inner diameter, outer diameter, cross-section, and dimensional tolerances are checked against approved drawings and specifications to ensure proper groove fit.

  • Material & Hardness Inspection

Rubber material and Shore A hardness are verified against approved requirements to support compatibility with compressed air, lubricants, and operating conditions.

  • Visual & Surface Inspection

Pneumatic O rings are checked for cracks, cuts, bubbles, flash, and other surface defects that may cause leakage or premature failure.

  • Sealing Performance Verification

Samples are evaluated under specified pressure, temperature, and static or reciprocating conditions to check leakage, friction, and sealing stability.

  • Production Process Control

Molding and vulcanization parameters are controlled to maintain dimensional consistency and stable rubber properties across production batches.

  • Batch Traceability

Production batches and material records are maintained to support quality investigations, repeat orders, and corrective actions.

  • Material Change Control

Changes to rubber compounds, raw materials, hardness, or manufacturing processes are reviewed against approved specifications to reduce the risk of inconsistent sealing performance.

  • Sample Approval & Final Inspection

Pre-production samples are checked against agreed requirements, and finished products undergo final inspection before shipment.

  • Cleanliness, Packaging & Storage

Pneumatic O rings are protected from contamination, deformation, heat, and sunlight during packaging and storage to help preserve product condition before installation.

Zhonggao's quality system includes dedicated QC personnel, laboratory testing equipment, raw-material inspection, and finished-product inspection, with IATF 16949, ISO 9001, ISO 14001, and ISO 45001 certifications.

View Our Quality Inspection Process

 

 

B2B Ordering & Supply Support

 

Flexible MOQ: MOQ depends on material, dimensions, tooling, and order requirements, supporting both trial orders and repeat bulk purchases.

Sample Lead Time: Typically 3–15 days, allowing buyers to check dimensions, material, and fit before mass production.

Bulk Production Lead Time: Typically 10–30 days after order details and production are confirmed, helping buyers plan replenishment and production schedules.

Packaging & Identification: Packaging and labeling can be arranged by size, material, batch number, or customer part number to simplify warehouse handling and repeat ordering.

Trade Terms: Available trade terms, such as EXW, FOB, CIF, or DDP, can be discussed according to the order and destination, helping buyers clarify shipping responsibilities and landed costs.

Quality Guarantee: A one-year quality guarantee covers manufacturing defects under normal use, providing support if qualifying product issues arise.

Learn More About Ningbo Zhonggao

image (1).webp

 

 

FAQ

 

Q: Why does a pneumatic cylinder leak air even after replacing the O ring?

A: Air leakage may result from damaged sealing surfaces, incorrect groove dimensions, improper installation, or an O ring unsuitable for the operating conditions.

Q: Can pneumatic O rings be used in oil-free compressed air systems?

A: Yes, provided the selected rubber compound is compatible with the system`s temperature, moisture level, and other operating conditions.

Q: What causes stick-slip in pneumatic cylinder seals?

A: Stick-slip can occur when friction between the O ring and the sliding surface varies due to insufficient lubrication, surface finish, material properties, or excessive seal compression.

Q: How can I prevent O ring extrusion in pneumatic pneumatic valves?

A: Select the correct O ring dimensions and hardness, and verify the clearance gap and pressure conditions to reduce the risk of extrusion.

Q: Can I replace a pneumatic O ring with the same size but a different rubber material?

A: Not without checking compatibility, because different rubber compounds can have different swelling, friction, wear, and temperature-resistance characteristics.

Q: How should pneumatic O rings be stored to prevent premature aging?

A: Store pneumatic O rings in sealed packaging away from direct sunlight, heat sources, ozone-generating equipment, and conditions that could cause deformation.

 

 

Custom Pneumatic O Rings for Your Project
Send your drawing or sample, ID, cross-section diameter (CS), dimensional tolerances, rubber material and Shore A hardness, compressed-air conditions, operating temperature and pressure, moisture and lubricant exposure, static or reciprocating motion, stroke speed and cycle frequency, groove dimensions and clearance, target order quantity, annual demand, packaging and labeling requirements, shipping destination, and required delivery schedule to receive a suitable pneumatic O ring quotation.

 

 

 

Hot Tags: pneumatic o ring, China pneumatic o ring manufacturers, suppliers, hydraulic cylinder o rings, large o rings, o ring 32mm x 2mm, oring 8x2, rectangular o ring, square cut o rings

 Creating Your Custom Rubber Parts Coupled with Our Masterly Manufacturing
 

OEM/ODM Services

 

Material Selection

 

Free Samples

 

Sample Delivery in 3-15 Days

 

Free Technical Consultation

 

24-Hour Response

Get A Free Quote