Ningbo Zhonggao Rubber & Plastic Manufacturing Co., Ltd. is one of the most reliable manufacturers and suppliers of y-ring in China. The company has world-leading production equipment and strong manufacturing capabilities. Welcome to wholesale custom made y-ring from our factory.
Y-Rings
Y-rings provide dynamic sealing for hydraulic and pneumatic cylinders, using a pressure-responsive Y-shaped profile to control fluid or air leakage during reciprocating movement. Proper profile, material, dimensions, and application matching help maintain reliable cylinder performance while reducing premature wear, leakage, and maintenance costs.
Technical Specifications
Rubber Material Selection:
|
Rubber Material |
Key Performance |
|
NBR |
Hydraulic Oil & Mineral Oil Resistance |
|
FKM |
High-Temperature Oils, Acids, Alkalis Resistance |
|
PU |
Abrasion & Tear Resistance |
|
PTFE |
Compatible with Almost All Media |
Y-Ring Specifications:
|
Parameter |
Typical Reference |
|
Operating Temperature |
NBR: −40 to +120°C; FKM: −20 to +200°C; PU: −40 to +90°C; PTFE: −100 to +280°C |
|
Hardness |
NBR: 70–90 Shore A; FKM: 75–90 Shore A; PU: 85–95 Shore A; PTFE: 60–70 Shore D* |
|
Working Pressure |
NBR: ≤25 MPa; FKM: ≤40 MPa; PU: ≤32 MPa; PTFE: ≤30 MPa |
|
Typical Reciprocating Speed |
NBR / FKM: ≤0.5 m/s; PU: ≤1.0 m/s; PTFE: ≤5.0 m/s |
|
Inside Diameter (ID) |
5–500 mm* |
|
Outside Diameter (OD) |
7–520 mm* |
|
Cross-Section Height |
2–20 mm* |
|
Radial Clearance |
0.05–0.30 mm* |
|
Axial Groove Width |
2.5–25 mm* |
|
Groove Depth |
1.5–15 mm* |
|
Shaft Surface Roughness (Ra) |
0.1–0.4 μm* |
|
Cylinder Bore Surface Roughness (Ra) |
0.2–0.8 μm* |
|
Installation Chamfer |
15–30°* |
|
Chamfer Length |
0.5–3.0 mm* |
|
Friction Reduction |
50% vs. comparable O-ring* |
|
Backup Ring |
1–2 rings where extrusion risk requires* |
|
Operating Frequency |
≤2 Hz typical reciprocating duty* |
|
Stroke Length |
10–2,000 mm typical* |
|
Cycle Life |
≥100,000 cycles under validated conditions* |
*Final specifications should be confirmed against the approved drawing, sample, and application requirements before production.
Custom Y-Rings
We manufacture custom Y-rings based on your drawing, sample, equipment, dimensions, and working conditions to match your sealing application.

Custom Size & Profile
We can produce:
- Custom ID, OD, height, cross-section, and critical dimensions
- Rod seals, piston seals, and application-specific Y-ring profiles
- Symmetrical or asymmetrical profiles where required
- Custom lip geometry, groove compatibility, and sealing configurations
Y-Ring Material & Hardness
Material and hardness can be selected according to:
- Hydraulic or pneumatic medium
- Operating and peak temperature
- Working pressure
- Reciprocating speed and stroke
- Friction, wear, and extrusion requirements
- Static or dynamic sealing conditions
Drawing / Sample
You can provide:
- CAD or technical drawings
- Rod, bore, and groove dimensions
- Critical dimensions and tolerances
- Existing Y-ring samples or OEM part numbers
- Equipment model and operating conditions
We can use these details to evaluate the sealing requirements and recommend a suitable Y-ring profile, material, and specification.
Custom Mold & Production
Custom molds can be developed for non-standard Y-rings. Available production options can include:
- Compression molding
- Transfer molding
- Injection molding
Samples can be produced for dimensional and application approval before mass production.
OEM & Custom Supply
We support custom:
- Dimensions and profiles
- Material and hardness
- Packaging and labeling
- Customer-specific part numbers
- OEM production based on customer drawings, samples, or molds
For customer-provided molds or project-specific tooling, the customer retains the exclusive right to use the tooling for the agreed project, while we maintain confidentiality over customer drawings, specifications, and related intellectual property.
Y-Ring Applications
Y-rings are used across hydraulic, pneumatic, mobile, and industrial equipment, with the suitable profile and material determined by the specific sealing position and operating conditions.
- Hydraulic Cylinders & Actuators
- Pneumatic Cylinders & Actuators
- Construction, Agricultural & Mobile Equipment
- Industrial Machinery & Hydraulic Systems
Y-Ring Manufacturing
Zhonggao supports prototype development, short-term production, and large-volume Y-ring orders through 20 production lines and a monthly production capacity of up to 10 million rubber parts. Production quantities such as 5,000, 50,000, or 500,000 pieces can be reviewed according to gasket design, tooling, material, and production schedule.
Requirement Review → Technical Confirmation → Sample Approval → Mass Production
Y-Ring Quality Control

-
Raw Material Inspection
Y-ring compounds are checked against the approved material, compound, and hardness requirements before production to verify material conformity.
-
Dimensional & Profile Inspection
Critical ID, OD, height, cross-section, lip geometry, and other dimensions are inspected against the approved drawing, specifications, and applicable tolerances.
-
Physical Property Testing
Applicable hardness, tensile strength, elongation, compression set, and other physical properties are tested according to the approved product requirements and relevant test methods.
-
Appearance Inspection
Finished Y-rings are inspected for surface defects, cracks, blisters, flash, foreign matter, deformation, damaged sealing lips, and other visible defects that could affect installation or sealing.
-
Finished Product & Batch Inspection
Finished Y-rings are checked against approved specifications before packing, while production, inspection, material, and applicable traceability records support consistent quality across repeat orders.
Zhonggao's quality system includes dedicated QC personnel, laboratory testing equipment, raw-material inspection, and finished-product inspection, with IATF 16949, ISO 9001, ISO 14001, and ISO 45001 certifications.
Y-Ring Ordering & Supply Support
The supply process can be arranged around the buyer's approved specifications, production quantity, delivery schedule, packaging requirements, and repeat-order needs.
- Sample Approval
- MOQ Discussion
- Production Scheduling
- Lead Time Confirmation
- Custom Packaging
- Product Labeling
- International Shipment
- Repeat-Order Support

Production & Supply Information
- Prototype & Sample Lead Time: Prototype and sample production is available before mass production, with a typical sample lead time of 3–15 days.
- Tooling: Custom mold development for molded gasket designs.
- MOQ: MOQ is flexible according to gasket size, process, tooling, and project requirements.
- Mass Production Lead Time: Small, medium, and large-volume orders are supported with a typical lead time of 10–30 days.
- Inspection Documents: Material and inspection reports available according to project requirements.
- Packaging: Bulk, bagged, labeled, barcode, or customer-specified packaging.
- Repeat Orders: Approved drawings, tooling, and production specifications can be retained for repeat production.
- Quality Issues: A 1-year quality guarantee is provided for qualified product quality issues.
FAQ
Q: Can a Y-Ring replace an O-ring in a hydraulic cylinder?
A: A Y-ring can replace an O-ring in some reciprocating applications, but the replacement should be confirmed based on sealing direction, groove geometry, pressure, speed, and available installation space.
Q: How do I know whether I need a rod Y-Ring or piston Y-Ring?
A: The correct type depends on whether the seal is installed around the moving rod or inside the piston and which pressure direction the seal must control.
Q: Are Y-Rings suitable for low-pressure pneumatic cylinders?
A: Yes, Y-rings can be used in pneumatic cylinders when the selected profile, material, lubrication, surface finish, and operating speed are suitable for the application.
Q: Do Y-Rings require lubrication during installation?
A: Most Y-ring installations benefit from compatible lubrication to reduce installation damage and initial friction, but the lubricant must be compatible with the seal material and working medium.
Q: Why does a Y-Ring leak after cylinder assembly?
A: Leakage after assembly can result from damaged sealing lips, incorrect installation direction, groove problems, excessive clearance, shaft or bore damage, or unsuitable seal specifications.
Q: Can Y-Rings be used with water-based hydraulic fluids?
A: Y-rings can be manufactured from compounds suitable for certain water-based fluids, but compatibility must be confirmed for the specific fluid concentration, temperature, pressure, and material.
Q: How should Y-Rings be stored before installation?
A: Y-rings should be stored in a cool, dry, clean environment away from direct sunlight, ozone sources, heat, and chemicals to minimize premature material aging.
Q: Can you supply Y-Rings according to an OEM part number?
A: Yes, an OEM part number can be used together with available dimensional or application information to identify or reproduce the required Y-ring specification.
Hot Tags: y-ring, China y-ring manufacturers, suppliers, o ring 4x1 5, split o ring, o ring 200mm, viton o rings, o ring 40 mm, brass o ring

