PTFE Encapsulated O Ring

PTFE Encapsulated O Ring
Product Introduction:
PTFE encapsulated O rings are important sealing components used in chemical processing, pharmaceutical equipment and industrial fluid handling systems. They are mainly used to prevent the leakage of liquids and gases while combining the chemical resistance of a PTFE outer layer with the elasticity of a rubber core, helping maintain reliable sealing in demanding operating environments.
Send Inquiry

Ningbo Zhonggao Rubber & Plastic Manufacturing Co., Ltd. is one of the most reliable manufacturers and suppliers of ptfe encapsulated o ring in China. The company has world-leading production equipment and strong manufacturing capabilities. Welcome to wholesale custom made ptfe encapsulated o ring from our factory.

 

PTFE Encapsulated O Rings

 

PTFE encapsulated O rings combine a chemically resistant FEP or PFA outer layer with an elastic core to support reliable sealing in demanding environments. Custom dimensions and material combinations help buyers match sealing requirements to specific equipment, media, temperature, and pressure conditions.

 

 

Technical Specifications

 

Rubber Material Combination Selection:

 

Material Combination

Key Performance

FEP + Silicone

Broad Chemical Resistance & Wide Temperature Flexibility

FEP + FKM

Chemical Resistance & Reliable Compression Recovery

PFA + Silicone

High-Temperature Resistance & Low-Temperature Flexibility

PFA + FKM

High-Temperature Jacket Performance & Compression Recovery

 

*The material combinations presented above are common options. Please verify the specific details based on your application requirements.

 

PTFE Encapsulated O Ring Specifications:

 

Specification

Value / Range

Encapsulation Material

FEP / PFA

Core Material

Silicone / FKM

Material Combinations

FEP + Silicone; FEP + FKM; PFA + Silicone; PFA + FKM

Operating Temperature

FEP + Silicone: −60°C to +205°C*; FEP + FKM: −20°C to +205°C*; PFA + Silicone: −60°C to +260°C*; PFA + FKM: −20°C to +205°C*

Hardness

Typically 85–95 Shore A after encapsulation*

Inner Diameter (ID)

6–5,000 mm*

Outer Diameter (OD)

OD=ID+2×CS*

Cross-Section (CS)

1.78 / 2.62 / 3.53 / 5.33 / 6.99 mm*

Operating Pressure

Up to 20 MPa*

Friction Coefficient

0.05–0.2*

 

*Actual dimensions, tolerances, temperature limits, pressure ratings, and material compatibility depend on the encapsulation and core materials, product construction, and operating conditions.

 

 

Custom PTFE Encapsulated O Ring Manufacturing

 

We manufacture custom PTFE encapsulated O ring requirements based on your drawings, samples, equipment dimensions, and sealing conditions.

image (15).png

 

Custom Size & Dimensions

  • Inner diameter (ID), outer diameter (OD), and cross-section (CS)
  • Dimensional tolerances and non-standard sizes
  • Installation groove dimensions, clearances, and fitting requirements
  • Replacement specifications based on existing O rings or approved drawings

 

Encapsulation & Core Material Selection

Choose the material combination according to operating conditions:

  • FEP + Silicone: Chemical resistance with flexible core performance
  • FEP + FKM: Chemical resistance with FKM core properties
  • PFA + Silicone: For applications requiring higher encapsulation temperature capability
  • PFA + FKM: For higher-temperature applications requiring an FKM core

Final material selection depends on the specific chemical media, concentration, operating temperature, pressure, and sealing requirements.

 

Operating Conditions & Sealing Requirements

Custom configurations can be assessed based on:

  • Contact media, chemical concentration, and cleaning agents
  • Continuous and peak operating temperatures
  • Working pressure, vacuum, and pressure cycling
  • Static or dynamic sealing conditions
  • Leakage limits and expected service life

 

Drawing & Sample-Based Customization

We customize PTFE encapsulated O rings based on your drawings, samples, or existing part specifications:

  • CAD or technical drawings with dimensions and tolerances
  • Existing O ring samples or part numbers
  • Encapsulation and core material requirements
  • Equipment groove dimensions and installation details
  • Contact media, operating temperature, and pressure conditions
  • Sample verification before bulk production

 

OEM & Replacement Support

  • Custom dimensions and approved material combinations
  • Replacement O rings matched to existing equipment requirements
  • Product identification, packaging quantities, and labeling specifications
  • Sample validation against approved specifications before bulk production

Please confirm the required dimensions, material combination, operating conditions, order quantity, and delivery schedule when requesting a quotation.

 

 

PTFE Encapsulated O Ring Applications

 

PTFE encapsulated O rings are used in a range of industrial applications where chemical compatibility, reliable sealing, and process-specific performance are essential.

  • Chemical Processing Equipment
  • Pumps & Valves
  • Fluid Transfer Systems
  • Industrial Equipment
  • High-Purity Process Systems

 

 

 

PTFE Encapsulated O Ring Manufacturing Capability

 

We operate 20 production lines with 20,000+ molds and a team of 40+ experienced technicians, supporting custom encapsulated O rings from material selection and prototype development to production and inspection. Our encapsulation process covers FEP / PFA jacket extrusion, core encapsulation, ring forming, and thermal fusion, helping buyers match sealing dimensions and material combinations to equipment requirements while supporting consistent quality across repeat orders.

 

 

Metric O Ring Quality Control

 

image.webp
  • Material & Core Verification

FEP or PFA encapsulation materials and Silicone or FKM core materials are checked against the approved material combination and application requirements.

  • Dimensional Inspection

Critical ID, OD, cross-section, and dimensional tolerances are checked against the approved drawing, sample, or specified size standard.

  • Encapsulation Integrity Inspection

The outer jacket is inspected for visible cracks, cuts, surface defects, and damage that could compromise sealing performance.

  • Sealing Performance Testing

Sealing performance is evaluated against specified operating conditions, including pressure, temperature, and contact media, where testing is required and available.

  • Sample Validation & Fit Approval

Samples are checked for dimensional fit, groove compatibility, and application suitability before the specifications are approved for bulk production.

  • Quality Documentation & Traceability

Material records, inspection results, and batch identification are provided according to the agreed documentation and traceability requirements.

Zhonggao's quality system includes dedicated QC personnel, laboratory testing equipment, raw-material inspection, and finished-product inspection, with IATF 16949, ISO 9001, ISO 14001, and ISO 45001 certifications.

View Our Quality Inspection Process

 

 

B2B Ordering & Supply Support

 

Sample & Bulk Lead Time: Sample preparation typically takes 3–15 days, with bulk production taking 10–30 days, depending on specifications and order quantity.

Flexible MOQ & Order Quantities: MOQ is determined by material combination, dimensions, and customization requirements to support both trial orders and repeat purchasing.

Trade Terms: FOB, EXW, CIF, and DDP terms can be discussed according to destination and shipping requirements.

Packaging & Quality Guarantee: Packaging and labeling can be arranged according to order requirements, with a 1-year quality guarantee subject to the agreed product terms.

Learn More About Ningbo Zhonggao

image (1).webp

 

 

FAQ

 

Q: Can PTFE encapsulated O rings be used for dynamic sealing?

A: They are primarily used for static sealing, while reciprocating or rotary applications require validation of friction, wear, and jacket durability.

Q: Why does a PTFE encapsulated O ring leak after installation?

A: Leakage may result from jacket damage, incorrect groove dimensions, excessive installation stretch, insufficient compression, or incompatible operating conditions.

Q: Can PTFE encapsulated O rings be installed in standard rubber O ring grooves?

A: Not always, because the encapsulated ring's overall dimensions and compression behavior may differ from those of a conventional elastomer O ring.

Q: How should PTFE encapsulated O rings be stored before installation?

A: Store them in clean, dry conditions away from direct sunlight, excessive heat, sharp objects, and deformation that could damage the encapsulating jacket.

Q: How can buyers prevent damage when installing PTFE encapsulated O rings?

A: Use clean, burr-free mating surfaces and compatible installation tools, and avoid twisting, stretching, or scraping the encapsulating jacket during assembly.

Q: Are PTFE encapsulated O rings suitable for food or pharmaceutical equipment?

A: Suitability depends on the specific material grades, cleanliness requirements, and applicable regulatory documentation, which should be verified before use.

Q: Can an existing PTFE encapsulated O ring be reverse-engineered from a sample?

A: A sample can help establish dimensions and construction requirements, but material identification and performance suitability may require additional documentation or testing.

Q: How is the quality of bulk PTFE encapsulated O rings verified before shipment?

A: Bulk orders are checked against approved drawings and material requirements, with dimensional and surface inspections and final pre-shipment inspection to help ensure consistent fit and encapsulation integrity.

 

 

Custom PTFE Encapsulated O Rings for Your Project
Send your drawing or sample, inner diameter, outer diameter, cross-section diameter, FEP or PFA encapsulation material, Silicone or FKM core material, contact media, operating temperature and pressure, sealing type, groove dimensions, order quantity, and required delivery schedule to receive a suitable PTFE encapsulated O ring quotation.

 

 

 

Hot Tags: ptfe encapsulated o ring, China ptfe encapsulated o ring manufacturers, suppliers, 12mm o ring, cryogenic o rings, o ring distributors, o rubber ring, oring 20x3, viton o ring manufacturers

 Creating Your Custom Rubber Parts Coupled with Our Masterly Manufacturing
 

OEM/ODM Services

 

Material Selection

 

Free Samples

 

Sample Delivery in 3-15 Days

 

Free Technical Consultation

 

24-Hour Response

Get A Free Quote